汽車分動箱鏈傳動安全匹配設計方法與試驗研究
本文關鍵詞: 分動箱 鏈傳動 匹配設計 試驗研究 出處:《機械傳動》2016年11期 論文類型:期刊論文
【摘要】:基于汽車分時驅動和全時驅動整車動力性能要求,研究了分動箱鏈傳動的匹配計算,分析了分動箱在各種典型工況下,其分動箱鏈條所承受載荷的計算方法,并據此提出安全匹配設計方法。介紹了分動箱鏈傳動的試驗方法并分析了試驗結果,列舉了分動箱選擇匹配設計實例。結果表明,汽車分動箱鏈條的匹配設計在滿足汽車分動箱動力分配的前提條件下,可以充分保證鏈傳動系統的疲勞性能和磨損性能,該方法對汽車領域四驅分動箱鏈傳動系統的自主開發具有重要的指導意義。
[Abstract]:Based on the dynamic performance requirements of the vehicle with time-sharing drive and full-time driving, the matching calculation of the chain drive of the shunting box is studied, and the calculation method of the load of the shunting box chain under various typical working conditions is analyzed. According to this, the design method of safety matching is put forward. The test method of chain drive of shunt box is introduced, and the test results are analyzed, and an example of selecting matching design of shunt box is given. The result shows that. The matching design of automobile shunt box chain can fully guarantee the fatigue and wear performance of the chain transmission system under the precondition of satisfying the power distribution of the automobile shunting box. This method has important guiding significance for the independent development of the chain drive system of four-drive split-box in automobile field.
【作者單位】: 杭州東華鏈條集團有限公司;吉林大學鏈傳動研究所;
【基金】:國家自然科學基金(51275207)
【分類號】:U463.2
【正文快照】: 0引言分動箱總成是四驅汽車發動機動力分配的核心部件,目前一般有齒輪式和鏈?zhǔn)絻煞N結構形式。鏈?zhǔn)浇Y(jié)構以其體積小、質量輕、傳動轉矩大等優點得到越來越廣泛的應用。由于分動箱工作在高速、大載荷以及速度和載荷交變的條件下,因此,特別適合于采用圓銷式齒形鏈或變節距滾銷式齒
【相似文獻】
相關期刊論文 前10條
1 盛海林;分動箱外殼鏜孔工藝的改進[J];組合機床通訊;1977年01期
2 朱長建;;程序控制的分動箱高低檔切換方法研究[J];汽車電器;2010年01期
3 丁素珍,胡小平;分動箱體換檔軌孔工藝改進及誤差分析[J];麗水師范?茖W(xué)校學報;2002年05期
4 ;問車熱線[J];汽車知識;2011年12期
5 ;分動箱[J];二汽科技通訊;1975年02期
6 張閩魯;SAE PAPER[J];國外拖拉機;1982年07期
7 俞志平;;汽車分動箱殼體設計與分析[J];輕型汽車技術;2011年04期
8 魏秉中;雪佛蘭開拓者分動箱診斷代碼的診斷[J];汽車實用技術;2003年09期
9 曹曉龍;徐永綏;遲興國;;290型軌道車換向分動箱的設計[J];內燃機車;2008年05期
10 郭瑞金,J.Poirier,F.Chagnon,J.A.Danaher,M.Gagné,E.Ilia,S.Krise,韓鳳麟;用燒結硬化工藝生產汽車分動箱鏈輪[J];粉末冶金技術;2003年06期
相關重要報紙文章 前1條
1 盧瓊玉;杭齒試制成功HCF1200分動箱[N];中國工業報;2009年
相關碩士學位論文 前3條
1 高文杰;用于單發工程車底盤的模塊化取力分動箱結構及性能研究[D];長安大學;2015年
2 智東輝;用于單發工程車底盤的取力分動箱信息化設計及性能研究[D];長安大學;2015年
3 曹曉龍;290馬力軌道車機械換向分動箱設計[D];大連交通大學;2008年
,本文編號:1447775
本文鏈接:http://www.sikaile.net/kejilunwen/qiche/1447775.html