本文選題：醫學計量檢測 + 標準信號發生器�。� 參考：《中國測試》2017年10期

【摘要】：醫用運動平板參數的準確性直接關系到冠心病診斷的準確性,但目前國內尚無用于醫用運動平板心電分析系統溯源的標準信號發生器。為此,通過Matlab得到正弦波、方波和標準心率信號的波形數據,并存入單片機的內部Flash中,采用12位DAC和高頻晶振來保證輸出信號峰峰值和頻率調節的精度,將輸出信號經過電壓跟隨器后通過衰減器進行幅值的衰減以得到微弱信號。實驗表明:該標準信號發生器輸出的3種微弱信號頻率的最大相對誤差分別為1.6×10-2%、4.3×10-3%、-3.3×10-3%,峰峰值的最大擴展不確定度分別為0.38%、0.38%、0.54%,均達到設定的技術指標要求,滿足醫用運動平板心電分析系統的溯源要求。
[Abstract]:The accuracy of the medical motion plate parameters is directly related to the accuracy of the diagnosis of coronary heart disease, but at present there is no standard signal generator used for tracing the source of medical electrocardiogram analysis system in China. To this end, the waveform numbers of sine wave, square wave and standard heart rate signal are obtained by Matlab, and the 12 bit D is used in the internal Flash of the single chip microcomputer. AC and high frequency crystal oscillator are used to ensure the accuracy of peak peak value and frequency regulation of the output signal. The output signal passes through the follower and attenuates the amplitude by the attenuator to get the weak signal. The experiment shows that the maximum phase pair error of the 3 weak signal frequencies of the standard signal generator is 1.6 x 10-2%, 4.3 x 10-3%, -3.3 x 10-3, respectively. The maximum expansion uncertainty of peak peak value is 0.38%, 0.38%, 0.54%, which all meet the requirements of the set technical indexes to meet the traceability requirements of the electrocardiogram analysis system for medical sports.
【作者單位】： 中國計量大學計量測試工程學院;杭州市質量技術監督檢測院;
【基金】：浙江省質監系統科研計劃項目(20150235)
【分類號】：R318
，

本文編號：1988097