本文選題：鈷鉻合金　切入點：剪切力　出處：《華西口腔醫學雜志》2014年02期

【摘要】：目的比較鑄造鈷鉻合金與選區激光熔化(SLM)鈷鉻合金金瓷結合強度的差異。方法用鑄造法和SLM技術制作鈷鉻合金試件各10個,在中間1/3區域熔附瓷粉,采用剪切力試驗測試金瓷結合強度并觀察斷裂類型。采用SPSS 13.0軟件中的t檢驗對結果進行統計學分析。結果鑄造組、SLM組剪切力分別為(33.11±4.98)、(30.94±5.98)MPa,二者間差異無統計學意義(P0.05)。樣本的斷裂類型為復合斷裂。結論 SLM鈷鉻合金修復體精密度較高,其金瓷結合強度與鑄造鈷鉻合金相近。
[Abstract]:Objective to compare the bonding strength between cast cobalt-chromium alloy and selective laser melting (SLM) cobalt-chromium alloy. Methods 10 cobalt-chromium alloy specimens were made by casting method and SLM technique, and the ceramic powder was fused in the middle 1 / 3 region. The shear stress test was used to test the bonding strength of metal-porcelain and the fracture type was observed. The results were statistically analyzed by t test in SPSS 13.0 software. Results the shear stress of casting group was 30.94 鹵5.98 MPA, respectively. There was no significant difference between the two groups. The fracture type of the sample is complex fracture. Conclusion the precision of SLM cobalt-chromium alloy prosthesis is high. Its metal-porcelain bonding strength is close to that of cast cobalt chromium alloy.
【作者單位】： 中國醫科大學口腔醫學院修復科;遼寧省口腔醫學研究所;中國科學院金屬研究所分析測試部;中國醫科大學口腔醫學院材料教研室;
【分類號】：R783.2

【參考文獻】

相關期刊論文 前6條

1 楊永強;吳偉輝;來克嫻;黃常帥;付凱旋;張榮明;;金屬零件選區激光熔化直接快速成形工藝及最新進展[J];航空制造技術;2006年02期

2 吳芝凱;許勝;李寧;;固態相變對鈷鉻合金的金瓷匹配性的影響[J];華西口腔醫學雜志;2011年06期

3 廖雋琨;葉劍濤;朱峰;張翠翠;溫小姍;張藝萍;李博華;;不同熱處理?xiàng)l件對鈷鉻合金金瓷結合強度的影響[J];上海口腔醫學;2011年06期

4 趙祥宇;戰德松;孫毅;范U，

本文編號：1673182