電子設備電磁干擾分析的高效時域算法研究
發布時間：2018-07-24 08:06
【摘要】：隨著無線通信技術和脈沖技術的發展,空間電磁環境變得日益復雜。處于復雜電磁環境中的電子設備,容易受到外界電磁波的電磁干擾。為了保證電子設備的正常工作以及更好地指導電子設備的電磁防護設計,需要一套計算模型和數值方法來分析電子設備的電磁干擾問題。目前,采用數值方法分析電子設備的電磁干擾問題仍具有很大的挑戰性。為此,本文較系統地研究了多種高效的時域混合算法,用于電子設備場線耦合問題以及場路混合問題的模擬和分析。本文的主要工作和創新點總結如下：一、發展了無限大地面上長電纜電磁耦合的快速計算方法。首先,建立了地面上多導體發射線對多導體受擾線的串擾模型,分析了多導體受擾線端接負載的串擾響應特性。然后,提出了一種地面上長電纜激勵場的快速計算方法,避免了對無限大地面的直接建模,然后結合傳輸線方程和FDTD方法,研究了一種高效的時域混合算法,能夠快速模擬電磁波耦合到地面上幾百米長電纜的瞬態響應,且占用內存很少,并分析了電磁脈沖對地面上長電纜的電磁耦合規律,同時解決了多個寬頻帶輻射源同時照射長電纜電磁耦合計算難的問題。在此基礎上,建立了地面上屏蔽電纜的電磁耦合模型,研究了屏蔽電纜的場線耦合算法,分析了屏蔽電纜接地狀態對皮電流和芯線響應的影響。二、研究了設備屏蔽腔內傳輸線電磁耦合的高效時域混合算法。首先研究了一種電磁仿真軟件與傳輸線方程相結合的時域混合算法,高效模擬了電磁波對電大尺寸設備屏蔽腔內傳輸線的電磁耦合問題。然后提出了一種FDTD混合算法與傳輸線方程相結合的時域混合算法(FDTD-TL算法),實現了設備屏蔽腔結構的快速建模,以及空間電磁場與傳輸線瞬態響應的同步計算。在此基礎上,將地面上長電纜耦合的時域混合算法和設備屏蔽腔內傳輸線耦合的時域混合算法模塊化并封裝,形成了場線耦合效應仿真軟件。三、實現了FDTD-TL算法的大規模并行計算�；诒本⿷梦锢砼c計算數學研究所研制的并行自適應結構網絡應用支撐軟件框架(JASMIN),研究了大規模并行FDTD算法。通過1kW微波源機箱和單層多尺度建筑物電磁耦合的數值模擬,驗證了算法的正確性。然后,將FDTD-TL算法與大規模并行FDTD算法結合起來并移植到JASMIN框架下,實現FDTD-TL算法的大規模并行計算,通過相應的算例驗證了FDTD-TL并行算法的正確性和高效性,并分析了大功率微波源磁控管電磁泄漏對內部傳輸線的電磁耦合特性。四、研究了集總加載線天線的電磁脈沖耦合效應及防護。提出了網格內置集總元件的FDTD處理新方法,并與細導線FDTD方法結合起來,形成高效的時域混合算法,模擬了電磁脈沖對集總加載線天線的耦合,分析了入射電磁脈沖的類型以及脈沖寬度對天線上電流響應的影響,為天線進行前門防護設計提供理論依據。然后針對工作于50MHz-110MHz的超短波天線,設計了一款前門防護模塊。通過電路仿真軟件對濾波電路和前門防護模塊電路進行了設計,并加工成實物進行測試,使其滿足指標要求。五、發展了電子設備電磁干擾分析的高效場路混合時域算法。結合FDTD-TL算法和電路分析方法,研究了一種新型的場路混合時域算法,用于電子設備貫通導線的電磁干擾分析�；诖骶S南等效定理,研究了貫通導線電磁耦合的等效電路模型,利用狀態變量法對貫通導線端接的集總電路進行電磁干擾分析。通過相應的數值算例驗證了該算法的正確性和高效性,并將該算法應用于電子設備貫通導線的濾波防護設計,取得很好的設計效果。提出了一種新型的時域S參數級聯技術,結合FDTD-TL算法,研究了一種新型的場路混合時域算法,用于電子設備內部傳輸線網絡的電磁干擾分析。根據時域S參數級聯技術,將傳輸線網絡分解成傳輸線與電路兩部分,將電路對傳輸線的作用通過S參數進行等效,對于各段傳輸線采用FDTD-TL算法進行場線耦合模擬,從而獲得傳輸線網絡的瞬態響應,通過相應的數值算例驗證了該算法的正確性和高效性。
[Abstract]:With the development of wireless communication technology and pulse technology, the space electromagnetic environment becomes increasingly complex. The electronic devices in the complex electromagnetic environment are vulnerable to electromagnetic interference from the external electromagnetic waves. In order to ensure the normal work of the electronic equipment and better guide the electrical and magnetic protection design of the electronic equipment, a set of calculation model and numerical value are needed. Method to analyze the electromagnetic interference of electronic equipment. At present, it is still very challenging to use numerical methods to analyze the electromagnetic interference problem of electronic equipment. Therefore, a variety of efficient time-domain hybrid algorithms are systematically studied in this paper, which are used for simulation and analysis of field line coupling problems and field road mixing problems in electronic equipment. The main work and innovation points are summarized as follows: first, the fast calculation method for the electromagnetic coupling of long cables on the infinite ground is developed. First, the crosstalk model of the multi conductor transmission line on the ground is established, and the crosstalk response characteristic of the load on the end of the multi conductor interference line is analyzed. Then a long cable excitation on the ground is proposed. The fast calculation method of the excited field avoids the direct modeling of the infinite ground. Then, combining the transmission line equation and the FDTD method, a highly efficient time-domain hybrid algorithm is studied. It can quickly simulate the transient response of the electromagnetic wave coupled to the ground hundreds of meters long cable and occupies little memory, and analyses the long power of the electromagnetic pulse to the ground. The electromagnetic coupling law of the cable solves the problem of the electromagnetic coupling calculation of the long cable with multiple broadband radiation sources at the same time. On this basis, the electromagnetic coupling model of the shielded cable on the ground is set up, the field line coupling algorithm of the shielded cable is studied, and the influence of the grounding state of the shielded cable on the skin current and the response of the core line is analyzed. Two, the efficient time domain hybrid algorithm for electromagnetic coupling of transmission line in the shielding cavity is studied. First, a time-domain hybrid algorithm combined with electromagnetic simulation software and transmission line equation is studied. The electromagnetic coupling problem of electromagnetic wave to the transmission line in the shielding cavity of large size equipment is efficiently simulated. Then a hybrid FDTD algorithm and transmission are proposed. The time domain hybrid algorithm (FDTD-TL algorithm) combined with the transmission line equation realizes the rapid modeling of the structure of the shielding cavity of the equipment and the synchronous calculation of the transient response of the space electromagnetic field and the transmission line. On this basis, the time domain hybrid algorithm of the long cable coupled in the ground and the time domain hybrid algorithm of the transmission line coupling in the shielding cavity of the equipment is modularized and The field line coupling effect simulation software is formed. Three, the large-scale parallel computing of the FDTD-TL algorithm is realized. Based on the parallel adaptive structure network application support software framework (JASMIN) developed by the Beijing Applied Physics and Computing Mathematics Research Institute, the large-scale parallel FDTD algorithm is studied. The 1kW microwave source chassis and the single layer multi-scale architecture are used. The validity of the algorithm is verified by the numerical simulation of the electromagnetic coupling. Then, the FDTD-TL algorithm is combined with the large-scale parallel FDTD algorithm and transplanted into the JASMIN framework to realize the large-scale parallel computation of the FDTD-TL algorithm. The correctness and efficiency of the FDTD-TL parallel algorithm are verified by the corresponding calculation examples, and the high-power microwave source is analyzed. The electromagnetic coupling characteristics of the magnetron leakage to the internal transmission line. Four, the electromagnetic pulse coupling effect and protection of the lumped load line antenna are studied. A new method of FDTD processing in the grid is put forward, which is combined with the thin wire FDTD method to form an efficient time domain hybrid algorithm, and the electromagnetic pulse is simulated on the lumped load line. The coupling of the antenna, the type of the incident electromagnetic pulse and the influence of the pulse width on the current response on the antenna, provide the theoretical basis for the front door protection design of the antenna. Then, a front door protection module is designed for the ultra short wave antenna working in the 50MHz-110MHz. The filter circuit and front door protection module are used by the circuit simulation software. The block circuit is designed and processed into material to be tested to meet the requirement of the target. Five, an efficient field road hybrid time domain algorithm is developed for electromagnetic interference analysis of electronic equipment. A new field path hybrid time domain algorithm is studied with FDTD-TL algorithm and circuit analysis method, which is used for the electromagnetic interference analysis of the connecting wire of electronic equipment. Based on the de Venan equivalent theorem, the equivalent circuit model of the electromagnetic coupling of the through wire is studied. The analysis of the electromagnetic interference is carried out by the state variable method. The correctness and efficiency of the algorithm are verified by the corresponding numerical examples, and the method is applied to the filtering protection of the connecting wire of the electronic equipment. A new kind of time-domain S parameter cascade technology is proposed. A new kind of field path hybrid time domain algorithm is studied with FDTD-TL algorithm, which is used to analyze the electromagnetic interference of the internal transmission line network of electronic devices. The transmission line network is decomposed into two parts of the transmission line and the circuit according to the S parameter cascade technology in the time domain. The effect of the circuit on the transmission line is equivalent by the S parameter, and the field line coupling is simulated by FDTD-TL algorithm for the transmission lines of each segment, thus the transient response of the transmission line network is obtained. The correctness and efficiency of the algorithm is verified by the corresponding numerical examples.
【學位授予單位】：西南交通大學
【學位級別】：博士
【學位授予年份】：2016
【分類號】：TN811;TN820
本文編號：2140750
[Abstract]:With the development of wireless communication technology and pulse technology, the space electromagnetic environment becomes increasingly complex. The electronic devices in the complex electromagnetic environment are vulnerable to electromagnetic interference from the external electromagnetic waves. In order to ensure the normal work of the electronic equipment and better guide the electrical and magnetic protection design of the electronic equipment, a set of calculation model and numerical value are needed. Method to analyze the electromagnetic interference of electronic equipment. At present, it is still very challenging to use numerical methods to analyze the electromagnetic interference problem of electronic equipment. Therefore, a variety of efficient time-domain hybrid algorithms are systematically studied in this paper, which are used for simulation and analysis of field line coupling problems and field road mixing problems in electronic equipment. The main work and innovation points are summarized as follows: first, the fast calculation method for the electromagnetic coupling of long cables on the infinite ground is developed. First, the crosstalk model of the multi conductor transmission line on the ground is established, and the crosstalk response characteristic of the load on the end of the multi conductor interference line is analyzed. Then a long cable excitation on the ground is proposed. The fast calculation method of the excited field avoids the direct modeling of the infinite ground. Then, combining the transmission line equation and the FDTD method, a highly efficient time-domain hybrid algorithm is studied. It can quickly simulate the transient response of the electromagnetic wave coupled to the ground hundreds of meters long cable and occupies little memory, and analyses the long power of the electromagnetic pulse to the ground. The electromagnetic coupling law of the cable solves the problem of the electromagnetic coupling calculation of the long cable with multiple broadband radiation sources at the same time. On this basis, the electromagnetic coupling model of the shielded cable on the ground is set up, the field line coupling algorithm of the shielded cable is studied, and the influence of the grounding state of the shielded cable on the skin current and the response of the core line is analyzed. Two, the efficient time domain hybrid algorithm for electromagnetic coupling of transmission line in the shielding cavity is studied. First, a time-domain hybrid algorithm combined with electromagnetic simulation software and transmission line equation is studied. The electromagnetic coupling problem of electromagnetic wave to the transmission line in the shielding cavity of large size equipment is efficiently simulated. Then a hybrid FDTD algorithm and transmission are proposed. The time domain hybrid algorithm (FDTD-TL algorithm) combined with the transmission line equation realizes the rapid modeling of the structure of the shielding cavity of the equipment and the synchronous calculation of the transient response of the space electromagnetic field and the transmission line. On this basis, the time domain hybrid algorithm of the long cable coupled in the ground and the time domain hybrid algorithm of the transmission line coupling in the shielding cavity of the equipment is modularized and The field line coupling effect simulation software is formed. Three, the large-scale parallel computing of the FDTD-TL algorithm is realized. Based on the parallel adaptive structure network application support software framework (JASMIN) developed by the Beijing Applied Physics and Computing Mathematics Research Institute, the large-scale parallel FDTD algorithm is studied. The 1kW microwave source chassis and the single layer multi-scale architecture are used. The validity of the algorithm is verified by the numerical simulation of the electromagnetic coupling. Then, the FDTD-TL algorithm is combined with the large-scale parallel FDTD algorithm and transplanted into the JASMIN framework to realize the large-scale parallel computation of the FDTD-TL algorithm. The correctness and efficiency of the FDTD-TL parallel algorithm are verified by the corresponding calculation examples, and the high-power microwave source is analyzed. The electromagnetic coupling characteristics of the magnetron leakage to the internal transmission line. Four, the electromagnetic pulse coupling effect and protection of the lumped load line antenna are studied. A new method of FDTD processing in the grid is put forward, which is combined with the thin wire FDTD method to form an efficient time domain hybrid algorithm, and the electromagnetic pulse is simulated on the lumped load line. The coupling of the antenna, the type of the incident electromagnetic pulse and the influence of the pulse width on the current response on the antenna, provide the theoretical basis for the front door protection design of the antenna. Then, a front door protection module is designed for the ultra short wave antenna working in the 50MHz-110MHz. The filter circuit and front door protection module are used by the circuit simulation software. The block circuit is designed and processed into material to be tested to meet the requirement of the target. Five, an efficient field road hybrid time domain algorithm is developed for electromagnetic interference analysis of electronic equipment. A new field path hybrid time domain algorithm is studied with FDTD-TL algorithm and circuit analysis method, which is used for the electromagnetic interference analysis of the connecting wire of electronic equipment. Based on the de Venan equivalent theorem, the equivalent circuit model of the electromagnetic coupling of the through wire is studied. The analysis of the electromagnetic interference is carried out by the state variable method. The correctness and efficiency of the algorithm are verified by the corresponding numerical examples, and the method is applied to the filtering protection of the connecting wire of the electronic equipment. A new kind of time-domain S parameter cascade technology is proposed. A new kind of field path hybrid time domain algorithm is studied with FDTD-TL algorithm, which is used to analyze the electromagnetic interference of the internal transmission line network of electronic devices. The transmission line network is decomposed into two parts of the transmission line and the circuit according to the S parameter cascade technology in the time domain. The effect of the circuit on the transmission line is equivalent by the S parameter, and the field line coupling is simulated by FDTD-TL algorithm for the transmission lines of each segment, thus the transient response of the transmission line network is obtained. The correctness and efficiency of the algorithm is verified by the corresponding numerical examples.
【學位授予單位】：西南交通大學
【學位級別】：博士
【學位授予年份】：2016
【分類號】：TN811;TN820
【相似文獻】
相關期刊論文 前10條
1 張建軍,宋書善;電磁干擾的途徑和抑制技術[J];濟南交通高等�？茖W校學報;1998年02期
2 張林昌;電磁干擾的危害[J];安全與電磁兼容;2001年01期
3 新光;電磁干擾及其解決措施[J];電子產品世界;2001年14期
4 吳輝;地鐵電磁干擾的處理[J];自動化博覽;2003年02期
5 陳睿琦,康文,齊欣;幾種實用的抑制電磁干擾的方法[J];電子器件;2004年04期
6 陳介華,白小明;嵌入式系統的電磁干擾的解決方法[J];自動化技術與應用;2004年12期
7 Greg Zimmer;;探討降低電磁干擾之道[J];電子測試;2006年09期
8 谷立新;;電磁干擾抑制技術[J];新課程研究(職業教育);2007年02期
9 王春露;;對電磁干擾的探討[J];科技創新導報;2009年14期
10 趙治華;張向明;李建軒;馬偉明;潘啟軍;陶濤;;互感耦合電磁干擾的對消方法[J];電工技術學報;2010年01期
相關會議論文 前10條
1 孟暉;劉星汛;;電磁干擾分析與抑制[A];天津市電機工程學會2009年學術年會論文集[C];2009年
2 陸健;侯冬云;;減小電磁干擾的搭接、屏蔽要求及試驗方法[A];第六屆全國電磁兼容性學術會議2004EMC論文集[C];2004年
3 張俊峰;李興國;婁國偉;;基于小波包的電磁干擾分析[A];2007年全國微波毫米波會議論文集（下冊）[C];2007年
4 常若艇;;工、科、醫設備的電磁干擾特性[A];全國電磁兼容學術會議論文集[C];2001年
5 齊俊臣;劉春和;封艷文;易當祥;;電子產品抗電磁干擾簡析[A];2008第六屆電子產品防護技術研討會論文集[C];2008年
6 田立輝;田野;董志;張吟;;某型飛機電臺干擾問題分析和測試[A];2012航空試驗測試技術學術交流會論文集[C];2012年
7 李貴良;鞠青山;;醫療電子儀器的電磁干擾防護[A];全省醫療設備管理研討會論文集[C];1998年
8 和強;宋中偉;趙嶸;;關于電磁干擾在電廠的分析[A];全國火電大機組（600MW級）競賽第十屆年會論文集[C];2006年
9 朱良平;蔣吉兵;劉芬;;航天測試電磁干擾分析及預防研究[A];全國第4屆信號和智能信息處理與應用學術會議論文集[C];2010年
10 馬文智;王小永;;變頻設備應用中的電磁干擾防治[A];2007短壁機械化開采專業委員會學術研討會論文集[C];2007年
相關重要報紙文章 前10條
1 趙立華;電磁干擾與防護技術（科普之窗）[N];人民日報;2002年
2 河南 張國光;電磁干擾的防護與評價[N];電子報;2011年
3 山東 張永貴 編譯;通過掃描電源的頻率降低電磁干擾[N];電子報;2013年
4 王竹青;剖析電腦的電磁干擾[N];電腦報;2002年
5 ;新模/數轉換技術降低電磁干擾[N];計算機世界;2003年
6 羅慶;電磁干擾亟需科學抑制[N];中國電力報;2003年
7 李明;防護綜合布線中的電磁干擾[N];中國計算機報;2001年
8 宋德明邋特約通訊員 嚴玉葆;精密雷達器材免受電磁干擾[N];解放軍報;2008年
9 ;雙屏蔽阻擋電磁干擾[N];中國計算機報;2005年
10 ;“銳晶先鋒”FP705 有效減少電磁干擾[N];中國計算機報;2002年
相關博士學位論文 前2條
1 田麗媛;雙電機混合動力系統電磁干擾分析及FlexRay網絡設計[D];吉林大學;2015年
2 葉志紅;電子設備電磁干擾分析的高效時域算法研究[D];西南交通大學;2016年
相關碩士學位論文 前10條
1 劉東升;發射場電磁干擾分析及仿真模型研究[D];蘭州大學;2011年
2 安普春;信號處理中的電磁干擾抑制方法研究[D];東北大學;2014年
3 易文平;增程式電動汽車輔助動力系統的電磁干擾分析與預測[D];吉林大學;2016年
4 吳昊;PWM驅動電機電磁干擾建模方法研究[D];電子科技大學;2016年
5 丁錦輝;基于臨界模式Boost PFC的傳導電磁干擾分析[D];南京師范大學;2016年
6 劉時宜;復雜機電裝備電磁干擾（EMI）現場測試技術研究[D];湖南大學;2015年
7 江丹;多電飛機系統的電磁傳導和輻射特性與抑制方法的研究[D];南京航空航天大學;2016年
8 王超;飛機EWIS布線電磁干擾及適航性研究[D];中國民航大學;2012年
9 黨杰;系統級電磁干擾仿真研究[D];山東大學;2016年
10 黃林柯;超導磁儲能系統電壓源型變流器電磁干擾分析[D];蘭州交通大學;2016年
，本文編號：2140750
本文鏈接：http://www.sikaile.net/shoufeilunwen/xxkjbs/2140750.html
最近更新
教材專著
