本文選題：產能比 + 射孔參數　； 參考：《西安石油大學》2015年碩士論文

【摘要】：在射孔完井的優化設計中,射孔參數對射孔效果的影響是最為顯著的,這些參數的改變將會在很大程度上決定射孔方案是否成功。運用半解析的方法分別建立了直井、斜井、水平井三種井型的產率比模型,考慮到射孔參數的復雜性和不準確性,建立了各種井型的表皮系數計算公式。根據所建立的模型,并用C Sharp開發了相應的集成計算軟件,能對不同射孔參數條件下直井、定向斜井、水平井的產能進行計算,也能針對射穿和未射穿污染帶時射孔參數對產率比的影響進行排序。運用雙因素分析,通過軟件進行大量產率比計算,根據計算數據分別得出各個射孔參數對油氣井產能的影響大小,并且繪制出其與油氣井產能比的關系圖表,以此為依據對各種射孔參數對于產率比的影響進行分析�？紤]到射孔參數對套管強度的影響,運用灰色關聯法對射孔參數的影響大小進行排序,然后運用優劣距離法對射孔參數進行優化組合分析,最后通過對于某區塊地層具體參數應用,結合所建立的模型和編制的軟件,提出了該區塊的射孔參數優化設計方案。
[Abstract]:In the optimal design of perforation completion, the perforation parameters have the most significant effect on the perforation effect, and the change of these parameters will largely determine the success of the perforation scheme.The productivity ratio models of three types of wells, vertical well, inclined well and horizontal well, are established by semi-analytical method. Considering the complexity and inaccuracy of perforation parameters, the formulas for calculating the skin coefficient of various well types are established.According to the established model, the corresponding integrated calculation software is developed with C Sharp, which can calculate the productivity of vertical well, directional inclined well and horizontal well under different perforation parameters.The influence of perforation parameters on the yield ratio can also be sorted.By means of two-factor analysis, a large number of productivity ratios are calculated by software. According to the calculated data, the influence of each perforation parameter on the productivity of oil and gas wells is obtained, and the relationship between the perforation parameters and the productivity ratio of oil and gas wells is drawn.Based on this, the influence of perforation parameters on yield ratio is analyzed.Considering the influence of perforating parameters on casing strength, the grey correlation method is used to sort the influence of perforating parameters, and then the optimal combination analysis of perforation parameters is carried out by using the method of superior and inferior distance.Finally, through the application of the formation parameters of a certain block, combined with the established model and the software, the optimum design scheme of perforation parameters of the block is put forward.
【學位授予單位】：西安石油大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TE257.1;TE328

【參考文獻】

相關期刊論文 前10條

1 王海東;孫新波;;國內外射孔技術發展綜述[J];爆破器材;2006年03期

2 吳銘德;;射孔與油氣井產能[J];測井技術;1992年06期

3 王建平;王曉冬;馬世東;;各向異性部分射開直井不穩定滲流理論研究[J];大慶石油地質與開發;2007年03期

4 曾凡輝;郭建春;徐嚴波;趙金洲;;壓裂水平井產能影響因素[J];石油勘探與開發;2007年04期

5 朱九成，，郎兆新，張麗華，寧正福;射孔油井產率比計算模型[J];石油勘探與開發;1995年05期

6 張琪,周生田,吳寧,李明忠;水平井氣液兩相變質量流的流動規律研究[J];石油大學學報(自然科學版);2002年06期

7 劉志軍,張公社,孫天建;射孔水平井一種新表皮效應模型[J];河南石油;2005年04期

8 楊志成;劉月田;陳方園;;改進的聚類法在水平井產能預測中的應用[J];石油地質與工程;2009年05期

9 唐愉拉;潘迎德;;有限元方法在射孔完井中的應用[J];石油學報;1989年03期

10 唐愉拉;潘迎德;祝渝培;;氣井非達西流射孔完井的有限元數值模擬研究[J];石油學報;1992年04期

本文編號：1737111