二類油層三元復合驅后微觀剩余油變化規律
本文選題:三元復合驅 切入點:剩余油 出處:《東北石油大學》2015年碩士論文
【摘要】:大慶油田自1960年投產至今,大部分區塊已進入采出液高含水階段。北一區斷東歷經基礎井網注水階段、井網加密增產階段以及聚合物等化學驅階段后,再次面臨高含水問題。而三元復合驅技術能夠在穩油控水方面起到一定積極作用,故此區塊采用三元復合驅技術以提高采收率。針對二類儲層物性特點,研究不同驅替方案的情況下,三元復合驅后孔隙內微觀剩余油賦存狀態、剩余油含量分布狀態以及剩余油組分分布狀態。不僅能夠?qū)崿F(xiàn)三元復合驅后儲層孔隙中微觀剩余油賦存狀態規律的可視化,同時也能夠為后續開采提供具有針對性意義的理論和數據基礎。針對大慶油田二類油層三元復合驅后剩余油的變化規律,本文主要選取300×10-3μm2、500×10-3μm2以及滲透率在二類油層范圍內的三層非均質巖心作為研究對象。通過室內實驗研究:三元驅替后,剩余油飽和度、剩余油組分以及剩余油類型受到滲透率、毛管數、以及滲透率級差的影響。在不同滲透率的情況下,滲透率的大小對殘余油飽和度、輕重組分指數以及各類型剩余油含量變化均起到一定作用,同時通過檢測發現角隅狀剩余油含量隨滲透率變化波動幅度較大。本文主要研究毛管數在10-3~10-1的情況下對驅替效果的影響,同時剩余油飽和度、剩余油組分指數隨著毛管數的增大而減小。各級別毛管數驅替后巖心中角隅狀剩余油在剩余油類型中所占比例最大,其次是簇狀、喉道狀剩余油,孔表薄膜狀剩余油含量最小。不難發現毛管數越大,各類型剩余油含量隨之減少。驅油效果與滲透率級差、平均滲透率以及滲透率韻律組合均有很大關系,滲透率級差越大,低滲層未動用剩余油含量越大,平均滲透率越大,各層內剩余油均隨之減少,沿程長度對剩余油飽和度以及輕重組分指數均有一定影響。通過檢測數據可知,由于滲透率級差、滲透率韻律組合不同,各層的4種類型剩余油含量也有很大差異。但角隅狀剩余油仍然所占比例最大,其次為簇狀剩余油、喉道狀剩余油,孔表薄膜狀剩余油含量最少。
[Abstract]:Daqing oilfield has been put into operation since 1960, has entered the most blocks of produced liquid in high water cut stage. North East a zone broken through the basic well pattern infilling water flooding stage, production stage and polymer chemical flooding stage, once again faced with high water content. And the three element composite technology can control the water in oil stabilization plays a certain positive role, therefore block by EOR technology. According to the three element composite layer physical properties of two kinds of reservoir, study the different displacement case, the micro residual oil occurrence state of three element composite pore, residual oil content distribution and residual oil distribution. Not only visual components to achieve three yuan compound drive after the reservoir microscopic residual oil occurrence regularity, but also can provide specific meaning of theory and data mining. The foundation for the subsequent two three reservoir in Daqing Oilfield Changes of residual oil after flooding, this paper selects three layers of heterogeneous cores in two reservoirs in the range of 300 * 10-3 m2500 * 10-3 m2 and permeability as the research object. Through the indoor experiment study: three yuan after the flooding, remaining oil saturation, residual oil component and residual oil by type permeability, capillary number, and the influence of permeability. The permeability in different circumstances, the size of the residual oil saturation, permeability, light and heavy fraction index and residual oil of various types of content change played a role, at the same time, through the detection of corner remaining oil content with the change of permeability large fluctuation. This paper mainly studies the capillary number in the case of 10-3~10-1 influence on the displacement effect, while the remaining oil saturation, residual oil component index decreases with increasing the capillary number. The level of capillary number water flooding core angle The remaining oil in the corner shape types of remaining oil in the largest proportion, followed by cluster, throat like residual oil, residual oil film like Kong Biao. It is not difficult to find the minimum content of capillary number increases, various types of residual oil content reduced. The oil displacement effect and permeability, the average permeability and great rhythm relationship of permeability is, the layer of unused residual oil content is low permeability, the average permeability increases, each layer of residual oil are reduced, along the length of the remaining oil saturation and heavy components have a certain impact index. Through the test data shows that, due to difference of permeability, permeability rhythm, residual the oil content of 4 types of each layer are also very different. But the remaining oil like corner still accounted for the largest proportion, followed by the remaining oil in clusters, throat like residual oil, pore film residual oil content was the least.
【學位授予單位】:東北石油大學
【學位級別】:碩士
【學位授予年份】:2015
【分類號】:TE357.46
【共引文獻】
相關期刊論文 前10條
1 伍曉林,侯兆偉,陳堅,倫世儀;產酸微生物作用大慶原油改善化學驅效果研究[J];哈爾濱工業大學學報;2005年09期
2 蘭宇博;;淺談杏北地區強堿三元復合驅工業化推廣中調配工藝結垢的幾點認識[J];中國石油和化工標準與質量;2012年03期
3 楊柳;;三元復合驅采出液的穩定性及破乳機理研究[J];河北化工;2008年05期
4 牛麗偉;劉曉光;;弱堿三元復合驅過程中黏度和界面張力變化規律實驗研究[J];海洋石油;2009年04期
5 黃小會;李華斌;程柯?lián)P;田小蘭;喬林;;高30斷塊油藏S/P二元復合驅室內實驗研究[J];海洋石油;2010年01期
6 張學佳;紀巍;康志軍;孫大勇;王建;那榮喜;;三元復合驅采油技術進展[J];杭州化工;2009年02期
7 張付生;張雅琴;謝慧專;張懷斌;;堿/表面活性劑/聚合物對乳液穩定性的影響[J];石油天然氣學報(江漢石油學院學報);2005年S6期
8 石莉莉;;雙河油田北塊聚合物驅后剩余油分布及進一步挖潛[J];石油天然氣學報(江漢石油學院學報);2006年04期
9 郭東紅;張飛宇;辛浩川;崔曉東;;以不同減渣為原料制備大慶油田復合驅用表面活性劑的可行性研究[J];精細與專用化學品;2006年09期
10 張付生;汪芳;張雅琴;張懷斌;卜家泰;;三元復合驅采出液用破乳劑研究及其現場試驗[J];精細與專用化學品;2009年24期
相關會議論文 前2條
1 任文化;徐典平;劉新倉;;杏二區西部三元復合驅油擴大性礦場試驗[A];三次采油技術研討會論文集[C];2003年
2 李洪生;馬艷;代亞宏;梁楊;趙春旭;;下二門油田H2Ⅱ油組二次聚合物驅提高采收率技術現場應用[A];提高油氣采收率技術文集[C];2009年
相關博士學位論文 前10條
1 李杰訓;北一區三元復合驅采出液的乳化與破乳研究[D];東北石油大學;2011年
2 郭蘭磊;聚合物驅提高原油采收率的動態規劃方法研究[D];中國石油大學;2010年
3 伍曉林;Brevibacillus Brevis和Bacillus Cereus MEOR機制的研究及在大慶油田的應用[D];江南大學;2005年
4 張英志;薩北開發區純西葡一油層組沉積構成及聚驅解堵增注研究[D];中國地質大學(北京);2006年
5 蘭玉波;化學驅波及系數和驅油效率的研究[D];大慶石油學院;2006年
6 孫靈輝;化學劑在多孔介質中傳輸機理研究[D];中國科學院研究生院(滲流流體力學研究所);2008年
7 熊生春;堿溶液在地層多孔介質中的輸運規律研究[D];中國科學院研究生院(滲流流體力學研究所);2009年
8 王大威;高產脂肽類生物表面活性劑菌株及其驅油機理研究[D];大慶石油學院;2009年
9 郝春雷;聚合物驅后油藏高效驅油菌種的構建[D];大慶石油學院;2009年
10 張志軍;三次采油用改性石油磺酸鈉的合成與性能研究[D];大連理工大學;2009年
相關碩士學位論文 前10條
1 宋偉杰;離子液體與表面活性劑相互作用及其在三次采油中應用研究[D];華東理工大學;2010年
2 孫萬成;薩南開發區南五區三元復合驅舉升防垢配套工藝技術研究[D];東北石油大學;2011年
3 陳東;錦16塊化學驅工業化礦場試驗布井方案研究[D];東北石油大學;2011年
4 段吉國;驅油用石油磺酸鹽表面活性劑合成工藝研究[D];東北石油大學;2011年
5 付勇;北二西二類油層弱堿三元復合驅動態開采規律研究[D];東北石油大學;2011年
6 張大鵬;三元復合驅動態開采規律研究[D];東北石油大學;2011年
7 張寧;聚合物驅后提高采收率技術研究[D];東北石油大學;2011年
8 馬鳳春;非均質油層聚驅后蒸汽驅提高采收率技術研究[D];東北石油大學;2011年
9 李強;弱堿三元復合驅注入端結垢機理與預測技術研究[D];東北石油大學;2011年
10 黃小會;高30高溫斷塊油藏化學驅提高采收率研究[D];成都理工大學;2011年
,本文編號:1661062
本文鏈接:http://www.sikaile.net/kejilunwen/shiyounenyuanlunwen/1661062.html