【摘要】：為了增強雙臥軸全尾砂膏體充填料攪拌機的攪拌效果,提高攪拌機生產能力,在前人研究的基礎上,開展了“雙臥軸全尾砂膏體充填料攪拌機葉片排列方式和葉片參數優化設計”課題研究,主要研究內容如下:(1)不同葉片排列方式的全尾砂膏體充填料攪拌機的攪拌效果仿真。分析比較了單向正排列、單向反排列和對稱排列方式對攪拌機攪拌效果的影響,提出了一種新的葉片排列方式—混合排列方式,并對四種葉片排列方式的全尾砂膏體充填料攪拌機內部流速場進行仿真,根據仿真結果驗證混合排列方式的優越性。(2)混合排列全尾砂膏體充填料攪拌機葉片參數優化。在葉片排列方式優化的基礎上,對雙臥軸全尾砂膏體充填料攪拌機葉片的兩個主要參數(葉片寬度和安裝角度)進行優化設計,提出葉片角度設計的約束條件和最合理的設計建議,以提高攪拌機生產能力。(3)葉片結構設計優化。通過對葉片結構模型的應力應變分析,優化葉片結構設計,對葉片結構設計的材質和結構形式提出建議。研究結果表明:混合排列方式的全尾砂膏體充填料攪拌機內部流場強度高,區域大,攪拌效果最佳;葉片寬度根據設備功率和生產能力要求確定,葉片角度最佳角度為49°;葉片的材質宜選擇經濟、耐磨的Q235。
[Abstract]:In order to enhance the mixing effect of the double horizontal shaft full tailing paste filling material mixer and improve the production capacity of the mixer, on the basis of previous studies, The research on the optimum design of blade arrangement and blade parameters of double horizontal shaft full tailing paste filling material mixer was carried out. The main contents are as follows: (1) the simulation of the mixing effect of the whole tailings paste filling mixer with different blade arrangement. This paper analyzes and compares the influence of unidirectional positive arrangement, unidirectional inverse arrangement and symmetrical arrangement on agitation effect of agitator, and puts forward a new arrangement mode of blade, that is, mixing arrangement. The flow field of four kinds of blade arrangement is simulated, and the superiority of the mixed arrangement is verified according to the simulation results. (2) the blade parameters of the mixed paste filling mixer are optimized. On the basis of the optimization of blade arrangement, two main parameters (blade width and installation angle) of double horizontal shaft full tailing paste filling mixer blade are optimized. The constraint conditions of blade angle design and the most reasonable design suggestions are put forward in order to increase the production capacity of mixer. (3) Blade structure design optimization. Through the stress and strain analysis of the blade structure model, the blade structure design is optimized, and the material and structure form of the blade structure design are suggested. The results show that the internal flow field intensity is high, the area is large and the mixing effect is the best, and the blade width is determined according to the requirements of equipment power and production capacity, and the optimum angle of blade angle is 49 擄. The material of blade should choose economy, wear-resistant Q235.
【學位授予單位】：南華大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TD403

【參考文獻】

相關期刊論文 前1條

1 肖瀟;樊新建;吳時強;;基于k-ε紊流模型的后臺階流流動特性研究[J];水利水運工程學報;2013年03期

，

本文編號：2410951