本文關鍵詞： 雙螺桿壓縮機 反向設計 嚙合線 轉子型線 動力學仿真　出處：《機械科學與技術》2016年10期 　論文類型：期刊論文

【摘要】：針對傳統的雙螺桿壓縮機轉子型線的正向設計方法,計算過程繁瑣復雜,且無法預判型線綜合性能的問題,在深入研究嚙合線與轉子型線間關系的基礎上,提出一種反向設計方法:通過設計嚙合線反求獲得陰陽轉子型線。建立反向設計時陰陽轉子的坐標轉換關系,基于嚙合原理推導反向設計陰陽轉子型線的具體過程,分別以幾種典型曲線作為嚙合線段反求陰陽轉子型線方程。在GHH型線的研究基礎上,自行設計了一條嚙合線,反向推導計算出一對陰陽轉子型線進行流體分析并與GHH型線對比,發現該反向設計轉子型線與GHH型線性能接近。結合實驗結果表明,反向設計方法可有效應用于螺桿轉子型線設計。
[Abstract]:In view of the traditional forward design method of rotor profile of twin-screw compressor, the calculation process is complicated, and the comprehensive performance of the profile line can not be forecasted. On the basis of deeply studying the relationship between meshing line and rotor profile line, In this paper, a reverse design method is put forward: the rotor profile of yin and yang is obtained by reverse design of meshing line, and the coordinate transformation relation of rotor of yin and yang in reverse design is established, and the concrete process of reverse design of profile of rotor of yin and yang is deduced based on the meshing principle. On the basis of the research of GHH profile, a meshing line is designed and a pair of yin-yang rotor profile lines are derived and analyzed by reverse derivation and compared with GHH type lines. It is found that the linear energy of the rotor profile of the reverse design is close to that of the GHH type. The experimental results show that the reverse design method can be effectively applied to the profile design of the screw rotor.
【作者單位】： 江蘇省食品先進制造裝備技術重點實驗室;江南大學理學院;
【基金】：國家自然科學基金項目(51275210,51105175) 江蘇省“六大人才高峰”(2013-ZBZZ-016) 江蘇省產學研項目(BY2013015-30)資助
【分類號】：TH45

【相似文獻】

相關期刊論文 前10條

1 王能員;剃齒中兩嚙合線相對位置與奇數接觸點的確定[J];機械設計與研究;1995年02期

2 金樹林;;關于εmax的推導[J];教材通訊;1988年03期

3 周勝;;齒輪滾刀嚙合線誤差在萬能工具顯微鏡上的測量[J];計量技術;1989年12期

4 鄒e，

本文編號：1535098