本文關鍵詞：再制造液壓泵性能檢測系統的研發　出處：《合肥工業大學》2013年碩士論文　論文類型：學位論文

  更多相關文章： 再制造 軸向柱塞泵 檢測系統 AMESim

【摘要】：本文以工程機械中常用的雙聯軸向柱塞泵為測試對象,設計了再制造軸向柱塞泵性能測試系統。通過對雙聯軸向柱塞泵的性能測試,可以對再制造軸向柱塞泵進行全面、準確的性能評估。 本文對軸向柱塞泵的工作原理、結構、控制方式等進行了研究,并依據液壓軸向柱塞泵的相關標準對再制造軸向柱塞泵的技術條件、性能指標進行了進一步的研究和分析。本文設計了再制造柱塞泵性能測試系統的基本液壓回路,然后根據測試對象的技術參數設定了該測試系統的相關技術指標,并利用系統的參數完成驗算。另外本文針對再制造柱塞泵性能測試液壓系統中的關鍵模塊進行了詳細的理論計算,繼而完成液壓系統的整體設計。 在完成液壓系統的整體設計的基礎上,本文利用仿真軟件AMESim對再制造液壓泵性能檢測系統搭建了模型,設置各部分模型參數,然后對其進行仿真,并對結果進行分析,證明了液壓系統的可行性,并得出液壓系統的關鍵元件結構參數對系統動態性能的影響情況。 最后本文對檢測系統做了以下試驗：跑合試驗、排量驗證試驗、容積效率試驗、沖擊試驗、變量特性試驗、高溫試驗。通過上述實驗,再制造軸向柱塞泵的性能可以得到全面、準確地評估。
[Abstract]:In this paper, the performance test system of remanufactured axial piston pump is designed, which is commonly used in construction machinery, and the performance of double axial piston pump is tested. The remanufacturing axial piston pump can be comprehensively and accurately evaluated. In this paper, the working principle, structure and control mode of axial piston pump are studied, and the technical conditions of remanufacturing axial piston pump are discussed according to the relevant standards of hydraulic axial piston pump. The performance index is further studied and analyzed. The basic hydraulic circuit of the performance test system of the remanufactured piston pump is designed in this paper. Then according to the technical parameters of the test object, set the relevant technical indicators of the test system. In addition, the key modules of the remanufacturing piston pump performance test hydraulic system are calculated in detail, and then the overall design of the hydraulic system is completed. On the basis of the whole design of hydraulic system, this paper uses the simulation software AMESim to build the model of the performance test system of the remanufactured hydraulic pump, set up each part of the model parameters, and then carry on the simulation to it. The results are analyzed, the feasibility of hydraulic system is proved, and the influence of structural parameters of key components of hydraulic system on the dynamic performance of the system is obtained. Finally, the test system is tested as follows: running-in test, displacement verification test, volumetric efficiency test, impact test, variable characteristic test, high-temperature test. The performance of the remanufactured axial piston pump can be evaluated comprehensively and accurately.
【學位授予單位】：合肥工業大學
【學位級別】：碩士
【學位授予年份】：2013
【分類號】：TH137.51;TP274

【參考文獻】

相關期刊論文 前10條

1 徐濱士,朱勝,馬世寧,劉世參,梁秀兵;裝備再制造工程學科的建設和發展[J];中國表面工程;2003年03期

2 張偉;劉仲謙;張紓;徐濱士;;綠色制造與再制造技術研究與發展[J];中國表面工程;2006年S1期

3 郭q，

本文編號：1422713