本文選題：波形片 + 回彈　； 參考：《鍛壓技術》2015年03期

【摘要】：以某離合器波形片為研究對象,利用Dynaform有限元軟件對波形片的成形回彈進行數值模擬,分析了波形片回彈前與回彈后的應力分布,研究了模具間隙及板料厚度對波形片回彈后成形高度的影響。模擬分析表明,波形片彎曲成形的圓角處變形比較劇烈,其應力值較其他區域值更大,且回彈后應力值的減小使得板料發生回彈,而回彈使得波形片成形高度降低,從而影響離合器從動盤總成的彈性;波形片的成形高度隨著模具間隙的增大而減小,而隨著板料厚度的增加而增大。試驗結果表明,當板料厚度分別為0.6和0.8mm時,試驗值與模擬值的誤差變化范圍分別為5.44%~7.54%和4.52%~5.93%,模擬結果與試驗結果取得較好的吻合性。
[Abstract]:Taking a clutch corrugated plate as an object of study, the forming springback of a wave-form sheet was simulated by using Dynaform finite element software, and the stress distribution before and after springback of the wave-form sheet was analyzed. The effects of die clearance and sheet metal thickness on the springback height of the corrugated sheet were studied. The simulation analysis shows that the deformation at the corner of the wavy sheet is more severe, and the stress value is larger than that in other regions, and the reduction of the springback stress value makes the sheet material rebound, and the springback results in the reduction of the forming height of the corrugated sheet. Thus, the elasticity of the clutch follower assembly is affected, and the forming height of the waveform plate decreases with the increase of the die clearance, and increases with the increase of the thickness of the sheet metal. The results show that when the thickness of sheet metal is 0. 6 and 0.8mm, the error range between the test value and the simulated value is 5.447.54% and 4.52% respectively. The simulation results are in good agreement with the test results.
【作者單位】： 江蘇食品藥品職業技術學院機電工程系;江蘇財經職業技術學院機械電子與信息工程學院;
【基金】：2013年度省科技支撐計劃(工業)重點項目課題(BE2013009-4) 淮安市工業支撐項目(HAG2011014)
【分類號】：TG386

【共引文獻】

相關期刊論文 前10條

1 龍玲;鄒云;殷國富;;基于有限元法的油孔卡環彎曲回彈分析及控制[J];機床與液壓;2012年03期

2 解婧陶;;板料成形數值模擬中回彈問題的處理[J];機電技術;2011年06期

3 蔡學瑜;U形件板料自由彎曲回彈角計算數學模型的研究[J];機電工程技術;2005年09期

4 胡康康;劉雪;彭雄奇;秦計生;堵同亮;;基于迭代式回彈補償?shù)挠|發彈簧片折彎模具設計[J];模具技術;2012年02期

5 陳國泉;魏禮建;;典型含大平面結構高強鋼零件回彈分析與控制[J];機電技術;2015年01期

6 劉曉晶;劉博;陳曉曉;潘強榮;張彥q，

本文編號：1777501