球墨鑄鐵軋輥的光纖激光合金化性能
本文關鍵詞: 球墨鑄鐵軋輥 光纖激光 合金化 耐磨性 維氏硬度 疲勞性能 亞共晶組織 共晶組織 出處:《沈陽工業大學學報》2015年01期 論文類型:期刊論文
【摘要】:為了提高球墨鑄鐵軋輥的使用性能,采用光纖激光合金化系統對軋輥表面的預置合金層進行激光掃描,在球墨鑄鐵軋輥表面形成了冶金結合的合金化層.在最佳工藝參數條件下,分析了合金化層的耐磨性能、維氏硬度、冷熱疲勞性能和顯微組織.結果表明,合金化后的球墨鑄鐵軋輥的耐磨性能約為基體的3倍,維氏硬度也得到了明顯提高,冷熱疲勞性能基本相同.合金化層由亞共晶組織構成,亞共晶組織初晶相由馬氏體(M)、未分解WC硬質相及共晶組織構成,共晶組織由馬氏體(M)與復雜碳化物(WC、Co6W6C和Fe3C)構成.合金化層深度約為0.4 mm且組織細小.
[Abstract]:In order to improve the performance of ductile iron roll, the laser scanning of the preset alloy layer on the surface of the roll was carried out by using the optical fiber laser alloying system. A metallurgical alloying layer was formed on the surface of ductile iron roll. The wear resistance, Vickers hardness, cold and hot fatigue properties and microstructure of the alloyed layer were analyzed under the optimum technological parameters. The wear resistance of the alloyed ductile iron roll is about 3 times of that of the matrix, and the Vickers hardness is obviously improved, and the cold and thermal fatigue properties are basically the same. The alloying layer is composed of hypoeutectic structure. The primary phase of hypoeutectic microstructure is composed of martensite, undecomposed WC hard phase and eutectic structure, and eutectic structure is composed of martensite M) and complex carbides. Co6W6C and Fe _ 3C). The depth of alloying layer is about 0.4 mm and the microstructure is fine.
【作者單位】: 沈陽工業大學材料科學與工程學院;鞍山煜宸科技有限公司研發部;最新激光技術研究中心研發部;
【基金】:2013—2014年國家外國專家局“高端外國專家項目”(GDW20122101064)
【分類號】:TG333.17
【正文快照】: 心研發部,愛知縣安城4460026)在冶金行業中,軋輥已經成為各大鋼鐵企業的極大消耗品之一,其使用性能和壽命直接影響鋼鐵企業的產品質量、生產成本和效率[1-2].當球墨鑄鐵軋輥工作時,被軋制件的溫度約為1 150~1 250℃,而球墨鑄鐵軋輥表面的瞬時溫度可達600~700℃.在軋制過程中,
【參考文獻】
相關期刊論文 前8條
1 ;Cavitation erosion behavior of WC coatings on CrNiMo stainless steel by laser alloying[J];International Journal of Minerals Metallurgy and Materials;2009年02期
2 汪選國;武永宇;;45Cr4NiMoV軋輥堆焊焊條堆焊工藝及性能研究[J];武漢理工大學學報(交通科學與工程版);2006年02期
3 楊雪;葉福興;崔崇;王惜寶;;HVOF噴涂亞微米級WC-12Co涂層的物相變化與耐磨損性能[J];熱噴涂技術;2009年02期
4 張偉;石淑琴;王瑞權;林波;;45鋼激光WC合金化組織與性能的研究[J];熱加工工藝;2011年08期
5 徐國建;殷德洋;杭爭翔;張偉;;激光堆焊Co基合金與VC混合粉末組織和性能[J];沈陽工業大學學報;2012年01期
6 許喬;王健;馬平;陳賢華;雷向陽;;先進光學制造技術進展[J];強激光與粒子束;2013年12期
7 徐國建;丁小粉;王志一;邢飛;黃雪;武斌斌;沓名宗春;;蒸汽發電機葉片激光堆焊層的性能[J];沈陽工業大學學報;2014年03期
8 王洪金;于峗;李小平;孫順平;;激光合金化制備WC顆粒增強復合層耐磨性研究[J];應用激光;2012年05期
【共引文獻】
相關期刊論文 前10條
1 侯國梁;周惠娣;安宇龍;趙曉琴;劉光;;鋁合金異形曲面熱噴涂涂層的制備及性能研究[J];表面技術;2010年03期
2 江強;周細應;;表面涂層抗空蝕性能的研究進展[J];材料保護;2012年01期
3 孫桂芳;劉常升;陳歲元;陶興啟;;軋輥的失效及其修復技術[J];材料導報;2007年06期
4 劉成龍;林英英;王sヶ,
本文編號:1448202
本文鏈接:http://www.sikaile.net/kejilunwen/jinshugongy/1448202.html