本文選題：冷軋雙相鋼 + 力學性能��； 參考：《機械工程學報》2017年12期

【摘要】：對兩個來自不同生產線的冷軋雙相鋼DP780試樣的主要力學性能進行比較,發現相同牌號的DP鋼產品性能有顯著差異。建立拉伸過程的有限元模型,將拉伸試驗和有限元仿真相結合,利用材料失效點主應變二次導數的變化規律準確預測DP780在拉伸過程中的縮頸和破裂。研究發現相同牌號的DP鋼產品成形極限亦有明顯不同。最后從延伸長度和極限應變兩方面定量分析應變強化指數n值和強度系數K值的變化對拉伸過程成形極限的影響。發現應變強化指數n值的變化對成形極限影響較大,強度系數K值的變化對成形極限影響較小。增大n值可以提高發生縮頸和破裂時的延伸長度和極限應變。
[Abstract]:The main mechanical properties of two cold-rolled double-phase steel DP780 samples from different production lines were compared and it was found that there were significant differences in the mechanical properties of DP steel products of the same grade. The finite element model of the tensile process is established. By combining the tensile test with the finite element simulation, the necking and fracture of DP780 during the tensile process is accurately predicted by using the variation law of the second derivative of the main strain at the failure point of the material. It is found that the forming limit of DP steel with the same grade is also different. Finally, the effects of strain strengthening exponent n and strength coefficient K on the forming limit of tensile process are analyzed quantitatively from the two aspects of extension length and ultimate strain. It is found that the variation of strain strengthening exponent n has a great influence on the forming limit, while the change of strength coefficient K has little effect on the forming limit. The extension length and ultimate strain of necking and rupture can be increased by increasing n value.
【作者單位】： 北京科技大學機械工程學院;
【基金】：國家十二五科技支撐計劃資助項目(2015BAF30B01)
【分類號】：TG142.1

【相似文獻】

相關期刊論文 前10條

1 張樹艷;馬敘;王志華;楊繼宏;楊全祿;呂麗莎;劉遠鋒;;冷軋深沖板應力成形極限的研究[J];重型機械;2013年02期

2 周亮 ,陳鶴崢;根據穩定理論建立的理論成形極限曲線[J];北京航空學院學報;1986年01期

3 林大為,屠挺生,戴一一,張順才;板料真實成形極限的測定及其應用[J];鍛壓技術;2001年03期

4 李立軍,祝洪川;薄鋼板成形極限曲線的研究[J];物理測試;2003年05期

5 陳R際，

本文編號：2091439