本文選題：滾珠絲杠副 + 精度保持性　； 參考：《南京理工大學》2017年碩士論文

【摘要】：論文以國家科技重大專項"功能部件測試試驗共性技術研究與能力建設(2016ZX04004007)"為背景,基于滾珠絲杠副精度保持性試驗臺,對滾珠絲杠副的精度保持性進行了研究和評估,并研究加速試驗方法提高試驗效率。針對國內滾珠絲杠副精度保持性及試驗研究相對落后的現狀,基于可靠性研究的理論,對滾珠絲杠副的精度保持性進行了分析。根據精度保持性的數學模型進行仿真計算,研究不同試驗應力對精度的影響并確定試驗應力及邊界條件。研究精度保持性評估方法和加速試驗方法。對精度保持性試驗前的環境應力篩選試驗進行方案設計,確定篩選方法,制定篩選流程,設計篩選應力條件及應力施加方法,對滾珠絲杠副樣件進行了篩選試驗,發現和排除了早期故障�；跐L珠絲杠副精度保持性試驗臺設計精度保持性試驗方案和流程,并設計精度和預緊力在線測量方法;采用恒定應力加速方法進行了精度保持性加速試驗,分析試驗數據并研究威布爾分布下的精度保持性評估方法,對分布參數和不同可靠度的精度保持性時間進行分析。設計基于步進應力加速的A+A加速試驗方案和數據評估方法,適用于工廠對滾珠絲杠副產品的精度保持性進行快速測定與分析。對精度保持性驗收試驗方法進行分析,選取合適的抽樣方案和統計試驗方案,運用已有的精度保持性與加速試驗方法,根據生產方和接收方能夠承擔的驗收風險等參數,對具體統計方案的案例進行分析,選擇合理的驗收方案號并對接收、拒收判決進行分析,并根據接收、拒收的判據對滾珠絲杠副的精度保持性進行估計。
[Abstract]:Based on the national science and technology major project "Research and capacity building of functional component test commonality technology", based on the precision retention test platform of ball screw, the paper studies and evaluates the accuracy retention of ball screw pair. The accelerated test method is also studied to improve the test efficiency. Based on the theory of reliability research, this paper analyzes the precision retention of ball screw pairs in accordance with the relative backward status of domestic ball screw pairs' precision retention and experimental research. According to the mathematical model of precision retention, the influence of different test stress on precision is studied and the test stress and boundary conditions are determined. Research accuracy retention evaluation method and accelerated test method. The environmental stress screening test before precision retention test was designed, the screening method was determined, the screening process was established, the screening stress condition and the stress application method were designed, and the screening test was carried out on the ball screw pair sample. Early failures were detected and eliminated. Based on the design scheme and flow chart of precision retention test rig for ball screw pair, the on-line measurement method of precision and preload is designed, and the precision retention test is carried out by using constant stress acceleration method. The test data are analyzed and the precision retention evaluation method under Weibull distribution is studied. The distribution parameters and the accuracy retention time of different reliability are analyzed. The A A accelerated test scheme and data evaluation method based on step stress acceleration are designed, which is suitable for the rapid measurement and analysis of the precision retention of the ball screw by-products in the factory. This paper analyzes the acceptance test method of precision retention, selects suitable sampling scheme and statistical test scheme, and applies the existing precision retention and acceleration test methods, according to the acceptance risk that the producer and receiver can bear, and so on. This paper analyzes the case of the specific statistical scheme, selects the reasonable acceptance scheme number, and analyzes the decision of receiving and rejecting, and estimates the accuracy retention of ball screw pair according to the criterion of receiving and rejecting.
【學位授予單位】：南京理工大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TG502.3

【參考文獻】

相關期刊論文 前10條

1 戴鵬;陶衛軍;丁聰;馮虎田;;滾珠絲杠副精度保持性試驗臺測控系統設計[J];機械制造與自動化;2016年03期

2 常永壽;馮虎田;韓軍;楊雪;;滾珠絲杠副可靠性試驗臺測控系統設計[J];組合機床與自動化加工技術;2016年02期

3 楊雪;陶衛軍;韓軍;馮虎田;;模擬工況下滾珠絲杠副精度檢測方法研究[J];組合機床與自動化加工技術;2016年01期

4 陳燁妍;歐屹;韓軍;馮虎田;;滾珠絲杠副可靠性試驗設備和試驗方法研究[J];機械制造與自動化;2015年03期

5 丁聰;馮虎田;歐屹;;滾珠絲杠副精度保持性加載裝置的設計與對比[J];組合機床與自動化加工技術;2015年01期

6 沈嘉禾;陶衛軍;馮虎田;屠國俊;;重載滾珠絲杠副可靠性設計與試驗方法研究[J];組合機床與自動化加工技術;2013年04期

7 李凌豐;劉彩芬;;滾珠絲杠副軸向變形分析[J];中國機械工程;2011年07期

8 吳永亮;陳國光;孟召麗;;基于步進應力加速壽命試驗的硅壓力傳感器壽命預測[J];電子測量技術;2009年12期

9 宋現春;姜洪奎;許向榮;張佐營;;高速滾珠絲杠副彈性變形的有限元分析[J];北京工業大學學報;2009年05期

10 高偉;趙選民;;混合指數分布恒定應力加速壽命試驗的統計分析[J];機械科學與技術;2006年08期

，

本文編號：1995456