本文選題：Sr變質 + ADC合金��； 參考：《中國有色金屬學報》2016年05期

【摘要】：利用MMD-1型銷盤式磨損試驗機,采用OM、SEM和EDS研究不同負載對Sr變質ADC12合金的摩擦磨損性能的影響,并探究其與合金顯微組織及力學性能的關系。結果表明:當添加0.05%Sr(質量分?jǐn)?shù))時,合金顯微組織中共晶Si相以顆粒狀或纖維狀均勻分布在晶界,富鐵相則呈短棒狀,此時合金力學性能最佳,且同一負載下其磨損量和摩擦因數均最低。當負載為100N時,因受到嚴重擠壓變形,合金表面氧化膜發生破壞;基體合金以塑性屈服和嚴重剝層磨損為主要磨損機理;而當Sr添加量為0.05%時,合金的磨損程度最低,以粘著磨損和磨粒磨損為主要磨損機理,其摩擦磨損性能最優異。
[Abstract]:The effects of different loads on the friction and wear properties of Sr modified ADC12 alloy were studied by using MMD-1 type pin disk wear tester with OMSEM and EDS, and the relationship between them and the microstructure and mechanical properties of the alloy was investigated. The results show that the eutectic Si phase in the microstructure of the alloy distributes uniformly in the grain boundary as granular or fibrous when the addition of 0.05 Sr (mass fraction) is added, and the rich iron phase is in the shape of a short rod, and the mechanical properties of the alloy are the best. Under the same load, the wear and friction coefficient are the lowest. When the load is 100N, the oxide film on the alloy surface is destroyed due to the severe extrusion deformation, the main wear mechanism of the alloy is plastic yield and serious delamination wear, while the wear degree of the alloy is the lowest when Sr addition is 0.05%. Adhesive wear and abrasive wear are the main wear mechanisms, the friction and wear performance is the best.
【作者單位】： 南昌大學機電工程學院材料加工工程系;南昌市輕合金材料制備與加工重點實驗室;
【基金】：國家自然科學基金資助(51364035) 教育部高等學校博士學科點專項科研基金聯合資助課題(20133601110001) 江西省教育廳落地計劃項目(KJLD14003) 黨外專家博士產學研合作計劃(2012-CYH-DW-XCL-002)~~
【分類號】：TG146.21

【相似文獻】

中國期刊全文數據庫 前6條

1 周亞民;彭小蘭;;LED用ADC12鋁合金材料性能優化研究[J];東莞理工學院學報;2014年03期

2 唐全波;姜巨福;王迎;;擠鑄、壓鑄ADC12鋁合金連桿端蓋的組織和性能比較[J];特種鑄造及有色合金;2010年09期

3 唐全波;姜巨福;王迎;;兩種工藝成形的ADC12鋁合金連桿的力學性能對比[J];熱加工工藝;2010年19期

4 張茂勛,官云琴,鄭玉朋;ADC12鋁合金在水蒸汽中的腐蝕行為[J];中國腐蝕與防護學報;2002年04期

5 石錦罡;姚輝;陳名海;劉寧;李清文;;Mg含量對ADC12鋁合金組織及性能的影響[J];熱處理;2011年04期

6 ;[J];;年期

中國重要會議論文全文數據庫 前1條

1 羅樂;;ADC12產品精煉前后質量對比[A];2011重慶市鑄造年會論文集[C];2011年

，

本文編號：1798194