本文選題：高強度鋼筋　切入點：彎箍　出處：《鍛壓技術》2017年01期

【摘要】：高強度鋼筋在彎箍機上進行彎箍加工成一定角度后,在殘余應力作用下鋼筋會產生回彈現象。為了提高箍筋角度的精度,需要考慮回彈角度對箍筋角度的影響�；趶椝苄詮澢貜椑碚�,考慮加工硬化影響的情況下,推導出箍筋角度與回彈角度的關系式。并基于彎箍轉盤幾何模型,推導出彎箍轉盤轉角與箍筋角度的關系。應用MARC有限元軟件建立彎箍模型,分析了彎箍成形速度、彎箍軸回轉半徑對鋼筋回彈角的影響。進行彎箍成形實驗,結果表明,彎箍成形速度對回彈角度影響較小,回彈角隨著彎箍軸回轉半徑的增大而增大,實驗結果與有限元模擬結果基本吻合。
[Abstract]:When the high strength steel bar is processed to a certain angle on the bending hoop machine, the steel bar will rebound under the action of residual stress.In order to improve the precision of stirrups angle, the effect of springback angle on stirrups angle should be considered.Based on elastic-plastic bending springback theory, the relationship between stirrups angle and springback angle is derived considering the effect of work hardening.Based on the geometric model, the relationship between the rotation angle of the bending hoop and the stirrups angle is deduced.The MARC finite element software is used to establish the bending hoop model. The influence of the forming speed and the rotation radius of the bending hoop shaft on the springback angle of the steel bar is analyzed.The results show that the effect of the forming speed on the springback angle is small, and the springback angle increases with the increase of the rotation radius of the bending hoop shaft. The experimental results are in good agreement with the finite element simulation results.
【作者單位】： 燕山大學繼續教育學院;燕山大學國家冷軋板帶裝備及工藝工程技術研究中心;
【基金】：秦皇島市科學技術研究與發展計劃項目(201502A013)
【分類號】：TG306

【相似文獻】

相關期刊論文 前5條

1 秦龍海;;回彈角的應用[J];航空工藝技術;1982年03期

2 胡星星;裘樂淼;張樹有;張輝;;基于混合響應面法的滾壓成型回彈角預測控制及應用[J];浙江大學學報(工學版);2013年11期

3 彭清;模具上幾種實用彎管技術[J];模具工業;1993年08期

4 肖寒;張士宏;周榮;盧德宏;;AZ31鎂合金擠壓型材溫?zé)釓埩@彎成形過程中的回彈特征(英文)[J];Transactions of Nonferrous Metals Society of China;2012年S2期

5 ;[J];;年期

，

本文編號：1713800