發布時間：2018-01-03 08:05

  本文關鍵詞：塑性強化材料輥式矯直力學行為研究　出處：《機械工程學報》2016年18期 　論文類型：期刊論文

  更多相關文章： 鋼板 矯直 塑性強化材料 應力 彎曲

【摘要】：采用彈塑性彎曲理論與應力線性疊加原則對塑性強化材料連續彈塑性彎曲過程力學行為進行分析,考慮應力傳遞效應對矯直過程的影響,建立七輥輥式矯直機連續彈塑性彎曲矯直過程力學模型。通過對比試驗結果及理論計算值,兩者偏差平均值在8%以內,驗證了理論分析方法的正確性。利用該模型,對不同的矯直策略進行分析。結果表明,大變形矯直策略殘余應力與殘余曲率控制能力均強于小變形矯直策略;由于應力傳遞效應對矯直過程的影響,使得小變形矯直策略隨矯直過程的深入,殘余曲率并未向零點逐步收斂,而是在一定范圍內波動;大變形矯直策略由于采用了逐步矯直的工藝設定思想,使其可以達到矯直的目的。這些分析結果為工業生產中矯直策略的選取提供了理論依據。
[Abstract]:The elastoplastic bending theory and the principle of linear superposition of stress are used to analyze the mechanical behavior of the continuous elastic-plastic bending process of plastic strengthened materials, and the effect of stress transfer effect on the straightening process is considered. The mechanical model of continuous elastic-plastic bending straightening process of seven-roll straightener is established. The average deviation between the two is less than 8% by comparing the experimental results and theoretical calculation values. The correctness of the theoretical analysis method is verified. Using this model, different straightening strategies are analyzed. The results show that the residual stress and curvature control ability of the large deformation straightening strategy is better than that of the small deformation straightening strategy. Due to the influence of stress transfer effect on the straightening process, the small deformation straightening strategy with the deepening of the straightening process, the residual curvature does not gradually converge to 00:00, but fluctuates in a certain range. The large deformation straightening strategy can achieve the purpose of straightening because of adopting the idea of step by step straightening technology. These results provide a theoretical basis for the selection of straightening strategy in industrial production.
【作者單位】： 北京科技大學高效軋制國家工程研究中心;機科發展科技股份有限公司;
【基金】：中央高�；究蒲袠I(yè)務費專項資金(FRF-IC-14-005) 北京市自然科學基金(3154035)資助項目
【分類號】：TG333.23
【正文快照】： 0前言*考慮到節能減排的需要,鋼材逐漸向高強方向發展。高強鋼板在生產過程中極易出現瓢曲或內應力不均,輥式矯直是改善鋼板質量尤其是消除瓢曲和內應力的主要途徑。實現矯直的基礎是金屬材料在較大彈塑性彎曲變形條件下,不論原始彎曲程度有多大差別,在彈復后所殘留的彎曲差別

【相似文獻】

相關期刊論文 前8條

1 滕國杰;;校直彎矩和校直曲率半徑的求法[J];鍛壓機械;1984年06期

2 余同希,章亮熾;塑性彎曲成形的研究進展[J];應用科學學報;1988年03期

3 官英平 ,趙軍;板料彈塑性彎曲應力應變中性層位置關系探討[J];塑性工程學報;2002年02期

4 曹仁煥,閻振h，

本文編號：1373066