本文選題：激光制造　切入點：激光加工參數　出處：《中國激光》2017年03期 　論文類型：期刊論文

【摘要】：利用皮秒激光在304不銹鋼上進行表面著色試驗研究。分析了皮秒激光對不銹鋼表面著色的機理,建立了表面色彩的模型。分別試驗研究了掃描線間距、掃描速度和脈沖能量等激光工藝參數對著色效果的影響。研究結果表明,改變線間距、掃描速度和功率均能對著色效果產生顯著影響,在掃描速度90~300μm/s,掃描線間距0.001~0.01mm,單脈沖能量60~140mJ/cm~2的參數范圍內能得到較好的色彩,而且三者對著色有近似的影響效果。在試驗基礎上,獲得了皮秒激光參數與CIE L*a*b*色彩模型之間的關系。最后對著色后的試樣進行了顏色老化對比試驗。老化對比試驗表明,不同老化時間下的激光著色試樣的色差值ΔE均很小,說明各試樣顏色接近,耐老化效果較好。
[Abstract]:The surface coloring of 304 stainless steel by picosecond laser was studied. The mechanism of surface coloration of stainless steel by picosecond laser was analyzed, and the model of surface color was established. The effects of laser parameters such as scanning speed and pulse energy on the coloring effect are studied. The results show that changing the line spacing, scanning speed and power can significantly affect the coloring effect. A good color can be obtained within the parameters of the scanning speed of 90 渭 m / s, the scan line spacing of 0.001 ~ 0.01mm, the single pulse energy of 60140mJ / cm ~ (-2), and the effect of the three factors on the coloring. The relationship between the parameters of picosecond laser and the color model of CIE has been obtained. Finally, the color aging contrast tests of the colored samples have been carried out. The results show that the color difference 螖 E of the laser colored samples at different aging times is very small. The results show that the color of each sample is close and the effect of aging resistance is better.
【作者單位】： 五邑大學機電工程學院;廣東省摩托車先進設計與制造工程技術研究中心;
【基金】：廣東省自然科學基金(S2013010008735)
【分類號】：TG177;TN249

【相似文獻】

相關期刊論文 前2條

1 黃天琪;李建美;路長厚;王愛群;張金琪;;Nd∶YAG納秒激光誘導304不銹鋼表面著色[J];應用激光;2013年06期

2 ;[J];;年期

相關重要報紙文章 前1條

1 鄒文;藝術版的“姚明神話”[N];人民日?qǐng)?bào)海外版;2007年

相關碩士學位論文 前1條

1 李廣武;不銹鋼表面著色與電化學拋光工藝的研究[D];山東大學;2005年

，

本文編號：1595951