本文選題：斜線齒面齒輪 + 齒根根切��； 參考：《中南大學學報(自然科學版)》2017年09期

【摘要】：為了滿足航空傳動的緊湊空間設計要求,研究一種新型點接觸斜線齒面齒輪及其齒寬設計。根據漸開線插齒刀方程,模擬插齒刀與工件的運動關系,推導斜線齒面齒輪的齒面方程;建立內端根切、外端變尖、限定工作齒高和避免二次切削等限制條件,計算面齒輪的有效齒寬。分析傾斜角、交點位置對內徑、外徑及齒寬的影響。研究結果表明:減小刀頂圓角半徑可避免齒根發生二次切削;增大傾斜角和交點位置的增量,面齒輪的內徑和外徑都增大,而有效齒寬卻減小。
[Abstract]:In order to meet the requirements of compact space design of aeronautical transmission, a new type of point contact bevel gear and its tooth width are studied. According to the equation of involute gear shaper, the kinematic relation between gear shaper and workpiece is simulated, the tooth surface equation of bevel gear is deduced, and the limiting conditions, such as cutting inner end root, sharpening outer end, limiting working tooth height and avoiding secondary cutting, are established. Calculate the effective tooth width of the face gear. The influence of inclination angle, intersection position on inner diameter, outer diameter and tooth width is analyzed. The results show that the secondary cutting of tooth root can be avoided by reducing the radius of the fillet of the top of the cutter, and increasing the increment of the angle of inclination and the position of intersection, the inner and outer diameters of the face gear will increase, but the width of the effective tooth will decrease.
【作者單位】： 長安大學道路施工技術與裝備教育部重點實驗室;重慶理工大學汽車零部件先進制造技術教育部重點實驗室;西北工業大學機電學院;
【基金】：國家自然科學基金資助項目(51205310,51375384) 陜西省自然科學基金資助項目(2015JQ5162) 中央高�；究蒲袠I(yè)務費專項資金資助項目(310825171003,310825161006) 汽車零部件先進制造技術教育部重點實驗室開放課題資助項目(2015KLMT06)~~
【分類號】：TH132.41

【相似文獻】

相關期刊論文 前10條

1 孫殿柱,董學朱;真實齒面嚙合分析[J];機械工程學報;2000年08期

2 孫殿柱,董學朱;描述真實齒面數學模型的研究[J];農業機械學報;2000年01期

3 劉祖愈;品良;;齒，

本文編號：1968547